OM‐00661‐04June 16, 1994Rev. C 06‐24‐14GORMAN‐RUPP PUMPSwww.grpumps.come 1994 Gorman‐Rupp Pumps Printed in U.S.A.INSTALLATION, OPERATION,AND MAINTENA
10 SERIES OM-00661PAGE B - 3INSTALLATIONSUCTION AND DISCHARGE PIPINGPump performance is adversely effected by increased suction lift, discharge eleva
OM-00661 10 SERIESPAGE B - 4 INSTALLATIONSuction Lines In SumpsIf a single suction line is installed in a sump, itshould be positioned away from the w
10 SERIES OM-00661PAGE B - 5INSTALLATIONDISCHARGE LINESSiphoningDo not terminate the discharge line at a level lowerthan that of the liquid being pump
OM-00661 10 SERIESPAGE B - 6 INSTALLATIONbe a full‐opening, ball‐type valve to prevent plugging by solids.A manual shut‐off valve should not beinstal
10 SERIES OM-00661PAGE B - 7INSTALLATIONDISCHARGE PIPEDISCHARGECHECK VALVEPUMP DISCHARGESELF‐PRIMINGCENTRIFUGALPUMPSUCTIONLINESUPPORTBRACKETCLEAN‐OUTC
OM-00661 10 SERIESPAGE B - 8 INSTALLATIONAdjusting the alignment in one directionmay alter the alignment in another direction. check each procedure a
10 SERIES OM-00661PAGE B - 9INSTALLATIONparts can catch clothing, fingers, ortools, causing severe injury to personnel.V‐BELT TENSIONINGGeneral Rules
OM-00661 10 SERIESPAGE B - 10 INSTALLATIONTable 1. Sheave Diameter (Inches)Deflection Force (Lbs.)CrossSectionSmallestSheaveDiameterRangeR.P.M.RangeUs
OM-0066110 SERIESOPERATION PAGE C - 1OPERATION - SECTION CReview all SAFETY information in Section A.Follow the instructions on all tags, labels andde
OM-00661 10 SERIESOPERATIONPAGE C - 2Consult the operating manual furnished with thepump power source before attempting to start thepower source.If an
Register your newGorman‐Rupp pump online atwww.grpumps.comValid serial number and e‐mail address required.RECORD YOUR PUMP MODEL AND SERIAL NUMBERPlea
OM-0066110 SERIESOPERATION PAGE C - 3Block the suction line and start the pump. At operating speed the pump should pull a vacuum of 20inches (508,0 m
OM-0066110 SERIESTROUBLESHOOTING PAGE D - 1TROUBLESHOOTING - SECTION DReview all SAFETY information in Section A.Before attempting to open or service
OM-00661 10 SERIESTROUBLESHOOTINGPAGE D - 2TROUBLE POSSIBLE CAUSE PROBABLE REMEDYPUMP STOPS ORFAILS TO DELIVERRATED FLOW ORPRESSURE (cont.)PUMP REQUIR
OM-0066110 SERIESTROUBLESHOOTING PAGE D - 3PREVENTIVE MAINTENANCESince pump applications are seldom identical, andpump wear is directly affected by su
10 SERIES OM-00661MAINTENANCE & REPAIR PAGE E - 1PUMP MAINTENANCE AND REPAIR ‐ SECTION EMAINTENANCE AND REPAIR OF THE WEARING PARTS OF THE PUMP WI
10 SERIESOM-00661MAINTENANCE & REPAIRPAGE E - 2SECTION DRAWINGPARTS PAGEFigure 1. Pump Model 14A22-B
ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY10 SERIES OM-00661MAINTENANCE & REPAIR PAGE E - 3PART
10 SERIESOM-00661MAINTENANCE & REPAIRPAGE E - 4PUMP AND SEAL DISASSEMBLYAND REASSEMBLYReview all SAFETY information in Section A.Follow the instru
OM-0066110 SERIESMAINTENANCE & REPAIR PAGE E - 5rate the check valve assembly from the check valveseat.Inspect the check valve parts for wear or d
10 SERIESOM-00661MAINTENANCE & REPAIRPAGE E - 6to the sleeve and work it up under the bellows.Slide the rotating portion of the seal off the sleev
TABLE OF CONTENTSiINTRODUCTION PAGE I - 1...SAFETY ‐ SECTION A PAGE A - 1...
OM-0066110 SERIESMAINTENANCE & REPAIR PAGE E - 7bearings. This may scratch the balls orraces and cause premature bearing failure.Rotate the beari
10 SERIESOM-00661MAINTENANCE & REPAIRPAGE E - 8Replace the bearing retainer O‐ring (22) in the pedestal and lubricate it with grease. Press the b
OM-0066110 SERIESMAINTENANCE & REPAIR PAGE E - 9IMPELLERSHAFTIMPELLERIMPELLERSHIMSSHAFTSLEEVEELEMENTSTATIONARYROTATINGELEMENTSTATIONARYSEALSPRINGS
10 SERIESOM-00661MAINTENANCE & REPAIRPAGE E - 10Impeller Installation and AdjustmentInspect the impeller, and replace it if cracked orbadly worn.
OM-0066110 SERIESMAINTENANCE & REPAIR PAGE E - 11tight, properly supported and secure. Open all thevalves in the suction and discharge lines.Be su
For U.S. and International Warranty Information,Please Visit www.grpumps.com/warrantyor call:U.S.: 419-755-1280International: +1-419-755-1352For Canad
TABLE OF CONTENTS(continued)iiTROUBLESHOOTING - SECTION D PAGE D - 1...PREVENTIVE MAINTENANCE PAGE D - 3...
10 SERIESOM-00661PAGE I - 1INTRODUCTIONINTRODUCTIONThank You for purchasing a Gorman‐Rupp pump.Read this manual carefully to learn how to safelyinstal
10 SERIESOM-00661PAGE A - 1SAFETYSAFETY ‐ SECTION AThis information applies to 10 Series basic pumps. Gorman‐Rupp has no control over or particular
10 SERIESOM-00661PAGE A - 2 SAFETYDo not remove plates, covers, gauges,pipe plugs, or fittings from an overheated pump. Vapor pressure within thepump
10 SERIES OM-00661PAGE B - 1INSTALLATIONINSTALLATION - SECTION BReview all SAFETY information in Section A.Since pump installations are seldom identic
OM-00661 10 SERIESPAGE B - 2 INSTALLATIONPREINSTALLATION INSPECTIONThe pump assembly was inspected and tested before shipment from the factory. Befo
Komentarze do niniejszej Instrukcji